| Customization: | Available |
|---|---|
| After-sales Service: | Online Technical Support |
| Warranty: | 2 Years |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Infitek REV-1005II Lab Digital Rotary Evaporator rotavapor
• The parts in contact with the material are all made of high borosilicate glass (expansion coefficient 3.3) and PTFE materials, which have stable performance and are not easy to react with the materials.
• The stent is made of cold plate anti-corrosive spray + aluminum alloy material, and the bath is made of 304 stainless steel.
• The sealing system uses PTFE + fluororubber compound sealing.
• Oily vacuum pressure gauge shows real-time vacuum by pointer.
• The piston-type feeding valve is sleeved with PTFE extension tube, which can be continuously fed to the evaporation bottle under vacuum status.
• Upright double-layer serpentine coil as condenser
• Large LCD display, which can control rotation, heating and lifting at the same time
• Using brushless deceleration booster motor as rotary motor, no spark and low noise.Lifting motor also uses this kind of motor.
• Thermostat controlled bath, with PT100 sensor + stainless steel probe at the bottom of bath
• The bath can be lifted electrically. A silicone cover is equipped outside the bath for heat insulation and anti-scalding.
• Rotating and heating double fuses safety protection
• The collection bottle has a lower discharging port, equipped with glass + PTFE independent discharge valve.
• There is a water discharging valve at the bottom of the bath to facilitate liquid discharge
• Vacuum switching valve can continuously collect and discharge materials without affecting the system vacuum and solution distillation
• Over-temperature protection function, when the actual temperature> setting temperature+5 ºC, the machine will automatically power off
• Anti-drying function, when the water level in the heating bath is lower than the heating tube, the machine will automatically power off
• If the power is suddenly cut off while the machine is working, the machine will automatically stop heating when the power is turned on again
| Model | REV-1005II |
| Voltage/Frequency | 220V 50Hz/110V 60Hz |
| Total Power | 2100W |
| Rotary motor power | 60W |
| Lifting motor power | 40W |
| Heating power | 2000W |
| Vacuum | 0.095Mpa |
| Rotary flask volume | 5LΦ230mm/Φ80 flange port |
| Collecting flask volume | 3LΦ195mm/upper Φ50 flange port×Φ35 flange port×2 pcs × lower Φ50 flange port |
| Rotary speed | 0-120rpm/min |
| Temperature control range | Room temperature-180ºC |
| Temperature control accuracy | ±1ºC |
| Bath lifting stroke | 140mm |
| Condenser dimension | Φ120×600H(mm) side Φ50 flange port × lower Φ50 flange port |
| Condensing area | 0.5*0.5m |
| Gas cylinder | Left Φ35 flange port, side Φ50 flange port, rightΦ50 flange port |
| Material feeding valve | Φ35 flange port, glass + PTFE valve, material feeding valve (pagoda joint) with 12mm outer diameter |
| Releasing valve | Φ35 flange port×2, glass + PTFE valve, releasing valve (pagoda joint)with 12mm outer diameter |
| Material discharging valve | Φ50 flange port, side discharging valve (pagoda joint) with 20mm outer diameter, 260mm from the ground |
| Vacuum nozzle | Pagoda joint with 10mm outer diameter |
| In and out circulating nozzle of condenser coil | Pagoda joint with 16mm outer diameter |
| Bath dimension/weight | Φ295×175H(mm) about 12L |
| Overall dimension(W*D*H) | 980×480×1260mm |
| Net weight | 46KG |
| Packing dimension | 800×450×1090mm wooden package 0.39m³ |
| Packing weight | 68KG |
1.What is the mechanism of manual lifting and auxiliary lifting of manual rotary evaporator?
The manual lifting part is a mechanical constant force lifting mode, which is safe, reliable, and low failure; the auxiliary lifting part is a stepless mechanical positioning adjustment.
2.Is it possible for a small rotary evaporator with a 5L evaporating flask?
It is not recommended to use this way, there is a risk. The excessive load of the glass shaft will cause the bearing parts to wear and reduce the life, which will affect the sealing performance. In severe cases, the shaft tube may be broken.
3.REV100-Pro can only rotate at a maximum of 280rpm when the forward and reverse rotation is set, and only 200rpm for one-way rotation. Why?
One-way rotation can reach 280rpm, no problem. To ensure safety, the maximum speed is limited to 200rpm.
4.Is it better to put the rotary steaming system in a fumehood?
It is better to put the rotary steaming system in a fume hood, and the taste can be discharged directly outside.
5.Is magnetic inspection required for air transportation?
There is a lifting motor, which requires magnetic inspection.
6.How to connect the rotary steaming and vacuum controller, and what is the function of the vacuum pump?
The vacuum controller is connected between the rotary steamer and the vacuum pump, in series. When using a rotary evaporation evaporator, the vacuum degree is not appropriate, and the reagents will suddenly boil and bump. By using a vacuum controller, in series with the rotary evaporation, the internal vacuum of the rotary evaporation can be accurately controlled, especially for the concentration of volatile reagents, which can achieve the maximum The most ideal recovery rate. It is also widely used in the vacuum distillation of organic reagents, the gradual control of the vacuum degree, and the gradual extraction of solvents.
){kind=link}